Options
氧化銦錫工廠中不同作業類型對粉塵產生之粒徑探討
Date Issued
2014
Author(s)
王思捷
Szu-Chieh Wang
Advisor
劉宏信
Abstract
有動物實驗與病例報告指出,氧化銦錫會對健康產生不良的影響,如細支氣管肺泡癌、肺腺瘤、鱗狀細胞癌、肺泡蛋白沉積症、肺部纖維化、巨噬細胞或發炎細胞浸潤等肺部病變。細小粉塵(粒徑小於1μm)進入人體後很容易進入肺部,由於其難溶特性不易排出體外,且相對於大顆粒來說有較大體表面積,因此更容易有肺部相關疾病發生。在台灣相關的調查報告不多,本研究目的是為了解使用氧化銦錫工廠中不同作業類型所產生之粉塵粒徑分布情況。 本研究使用八階型分徑採樣器(Marple)進行區域採樣,其粒徑(d50)分別為:0.13、0.52、0.96、1.55、3.5、6、9.8、 14.8、21.3、28.3 (μm),濾紙則是使用34mm,截取粒徑為0.5μm的PVC濾紙;個人採樣則是使用IOM個人採樣器,其濾紙為25mm,截取粒徑為5μm的MCE濾紙。分析方法為重量分析法,將採集到的濾紙重量以SigmaPlot與SPSS分析。 結果顯示無論是面板廠或靶材廠所採集到的粒徑分布中最高波峰峰值之d50主要為0.96μm,為超細顆粒(可呼吸性粉塵,會進入肺泡區),表示很容易造成肺部傷害,研磨時若使用砂紙號碼越大則產生較小的粉塵粒徑以IOM採集各面板廠以不同研磨工具所產生之粉塵濃度來說,面板廠中若使用環帶盤砂輪機的工廠所研磨出來的濃度最高(26.144mg/m3),而其次為圓盤砂輪機(濃度分別為7.672、9.722mg/m3)以及濃度最低的則是使用砂紙(濃度:5.307、15.211、5.824mg/m3)然而其中有一作業場所濃度較高,係因在研磨靶材時有使用塑膠布圍住;靶材廠中可呼吸性粉塵與總粉塵濃度差異不大,表示此類工作場所中大多的粒徑以可呼吸性粉塵為主,其中研磨區的濃度最高(研磨區濃度最高為3.782mg/m3),但銲合區主要的粒子為奈米粒子,因此需要特別注意。本研究發現,不論哪種作業類型,ITO粉塵的粒徑八成會沉降於氣管與支氣管區以及肺泡區,甚至超過百分之五十的顆粒粒徑位在肺泡區,甚至有奈米顆粒的產生,表示粉塵會容易沉積在體內造成人體傷害,強烈建議對銦暴露工作者應建立適當管理機制,這些包括確實配戴動力淨氣式呼吸防護具(Powered Air-purifying Particulate Respirators, PAPR)或工程改善措施。
AbstractFrom animal experiments and human cases report, inhalation of indium tin oxide (ITO) has adverse influence on human health such as bronchioloalveolar carcinoma, pulmonary adenomatosis, squamous cell carcinoma, pulmonary alveolar proteinosis, pulmonary fibrosis, macrophage infiltration. Also, ITO particles sized as the ultrafine particles (UFP less than 1μm) are more easily breathe into the lung with a bigger surface area relative to those larger particles to induce more lung diseases due to the characteristic of ITO particles difficultly dissolved in the lung. There is little research of indium tin oxide in Taiwan. The purpose of this study was to study the indium tin oxide particle size distribution in the different working type from various plants.The Marple 8-stage cascade impactors were used for area monitoring and IOM was used for personal sampling to collect samples. The Marple sampler consists of eight impaction stages(50% cut-off dae = 0.52, 0.96, 1.55, 3.5, 6.0, 9.8, 14.8, and 21.3 μm, respectively)and a back-up filter (34mm PVC with 0.5μm pore size). The IOM personal sampler was used the 25 mm MCE filter paper with 5μm pore size. The Sigma Plot and SPSS software package was used for data process and statistical analysis.The results showed that the particle size distribution at the peak d50 was at 0.96μm from both the ITO target and display panel plants. The particle size as the UFP can easily cause lung damages if using a larger number abrasive paper to generate such smaller particle size dust.The dust concentrations were collected by IOM from different tools for polishing ITO target in display panel factories. The belt sander generated the highest particle concentration (26.144 mg/m3), followed by the disc sander produced concentration (7.672 and 9.722 mg/m3), and the abrasive papers generated the lowest particle concentrations (5.307, 15.211, and 5.824 mg/m3).One workplace had high concentration (15.211 mg/m3) because plastic shield was used to surrounding the ITO target area for polishing. There is no difference between the total dust concentration and respirable dust concentration in the target plants. The result showed the respiable dust is the main composition among the target plants. A particle concentration of polishing areas in target plants can reach to the highest as 3.782 mg/m3. It should be noticed that the particle sizes in bonding area is nanometer-scaled and below the IOM limitation.In this study, we found that there are more than 80% the particle size distribution is in the trachea-bronchial region and pulmonary region from both ITO target and display panel plants. Even more than 50% the particle size is in the pulmonary region. It means that the dust will be breathed into the pulmonary alveolus easily. We strongly suggest that an appropriate management plan should be implemented for indium exposure workers. These include adequate usage of Powered Air-purifying Particulate Respirators(PAPR)and good engineering control strategies for indium exposure workers.Key words:indium-tin oxide (ITO) ‧Marple‧particle size‧Powered Air-purifying Particulate Respirators
Type
thesis
File(s)
No Thumbnail Available
Name
102CSMU5590002-001.zip
Size
10.78 MB
Format
Unknown
Checksum
(MD5):c459096c36307d5e3e97f608eddb97e1