燕敏Min Yan蔡俊毅Jyun-Yi Cai口腔科學研究所2026-03-179999/12/312017https://handle.ncl.edu.tw/11296/b6fy99https://scholars.csmu.edu.tw/handle/123456789/5521本研究的目的是評估四種氧化鋯陶瓷的光學和機械性質。實驗使用兩種一般氧化鋯陶瓷(CTC-White與Whitepeaks S),一種預染色的氧化鋯陶瓷(CTC-Precolor)和一種高透氧化鋯陶瓷(Whitepeaks S Ultra-T),和兩種玻璃陶瓷材料(ProCAD、e.maxCAD)作為對照組。將試片製作成直徑12.0mm及不同厚度(0.5 mm、0.8 mm與1.2 mm)的圓盤試片,用於L*、a*、b*的光學測試和雙軸彎曲測試(厚度:1.2 mm),然後使用L*、a*、b*值來計算半透明參數(TP)和蛋白光參數(OP)。使用Two-way ANOVA分析,之後再以Tukey’s test做事後檢定;雙軸撓曲強度則使用雙參數韋伯函數進行分析。結果顯示,四種氧化鋯材料的L*值與對照組的L*值有顯著的統計差異(p < 0.05)。CTC-Precolor和Whitepeaks S Ultra-T的TP值明顯高於一般氧化鋯塊(p < 0.05),並且試片的TP值隨著厚度的增加而降低,並且低於對照組(p < 0.05)。e.maxCAD和CTC-Precolor的OP值顯著高於一般氧化鋯(p < 0.05),此外在機械性質方面,與其他實驗組比較,Whitepeaks S有最高的雙軸彎曲強度,與CTC-White和CTC-Precolor有顯著的統計差異(p < 0.05)。韋伯函數分析結果顯示Whitepeaks S Ultra-T具有最高的韋伯模數,且分佈較集中,材料可靠度較高。本研究結果證明,Whitepeaks S Ultra-T高透氧化鋯和CTC-Precolor預染色氧化鋯材料有較為優良的半透明度和蛋白光效果,四種氧化鋯陶瓷均具有較高的雙軸彎曲強度。Objectives. The purpose of this study was to investigate the mechanical and optical properties of four kinds of zirconia ceramics.Methods. The general zirconia ceramic (CTC-W) and the pre-color zirconia ceramic (CTC-PC) and general zirconia ceramic (WPS) and high translucent zirconia ceramic (WPT) were served as the experimental group, and two commercial ceramics materials (PC and EC) were used as the control group. The different thickness (0.5 mm, 0.8 mm and 1.2 mm) disc specimens were fabricated with 12.0 mm in diameter for biaxial flexural strength and optical measurement in the L*, a* and b* values. Then the translucency parameter (TP) and opalescence parameter (OP) were calculated. The multivariate analysis, two-way ANOVA, and the Tukey HSD post hoc test (α = 0.05) were carried out.Results. No matter how thickness, The value (L*:90) of the general zirconia blanks was similar to the control group (89-92), lower value was shown in pre-color blanks (83). And a*(2.4-5.9), b* (24-28) was shown in pre-color blanks. The TP of specimens was significantly decreased with increasing thickness. The TP of CTC-PC and WPT was significant higher than the general zirconia blanks, however, it was lower than the control group. The OP of EC and CTC-PC was significant higher than the general zirconia blanks, In addition, the higher biaxial flexural strength (1561 MPa) was shown in WPS than the CTC-PC pre-color blanks (1047 MPa).Conclusions. These results shown that the WPT zirconia ceramic blanks and CTC-PC zirconia ceramic blanks have good mechanical、translucency and opalescence.氧化鋯光學性質雙軸彎曲強度半透明度蛋白光zirconiaoptical propertybiaxial flexural strengthtranslucencyopalescence四種氧化鋯的光學和機械性質研究thesis